Standard operating procedure
Forklift Pre-Shift Inspection
Prepared for your facility
- Facility
- your facility
- Document owner
- Warehouse manager
- Review cycle
- Annual, every year
- Shifts covered
- 2 shifts
- Applies to
- Certified forklift operators
Daily pre-shift examination of powered industrial trucks covering visual and operational checks, defect reporting, and out-of-service rules required before any forklift is placed in service.
1. Purpose
This procedure establishes the mandatory pre-shift inspection process for all powered industrial trucks (PITs). Its purpose is to identify unsafe conditions before a truck is placed in service, satisfy the daily examination requirement of 29 CFR 1910.178(q)(7), and ensure defective equipment is removed from service before it can injure an operator or pedestrian.
2. Scope
This procedure applies to every powered industrial truck operated at the facility, including sit-down counterbalance trucks, reach trucks, order pickers, and electric pallet jacks, and to every certified operator on every shift.
3. Responsibilities
Operators perform the inspection and report defects before operating. Supervisors verify inspections are completed and take defective trucks out of service. Maintenance personnel repair tagged trucks; only authorized personnel may perform repairs per 29 CFR 1910.178(p)(1).
4. Procedure: Visual Checks (Power Off)
With the truck powered off:
- Check tires and wheels for damage, wear, and embedded debris.
- Check forks for cracks, bends, and heel wear; verify fork locking pins.
- Inspect mast, chains, and hoses for damage, leaks, and lubrication.
- Verify overhead guard and load backrest are secure and undamaged.
- Check fluid levels or battery charge and connections as applicable.
- Confirm data plate is present and legible.
- Check seat belt condition and latching.
5. Procedure: Operational Checks (Power On)
In a clear area with the truck powered on:
- Test service brake and parking brake.
- Test steering through full range.
- Raise, lower, and tilt the mast through full travel.
- Test horn, lights, and backup alarm.
- Check hour meter and any warning indicators.
- Listen for unusual noises during operation.
6. Defect Reporting and Out-of-Service Rules
If any condition adversely affecting safety is found, the operator must not place the truck in service. Tag the truck out of service, remove the key, and report the defect immediately. The truck stays out of service until repaired by authorized personnel and re-inspected. Completed inspection records are retained per facility policy.
7. References
29 CFR 1910.178 Powered industrial trucks. Manufacturer operator manuals for each truck model. Facility traffic and pedestrian safety plan.
PPE required
- High-visibility vest
- Safety-toe footwear
Floor card
- Power off: check tires, forks, chains, mast, guard, seat belt
- Check battery or fuel; look for leaks under the truck
- Power on in a clear area
- Test brakes, steering, horn, lights, alarm
- Raise, lower, and tilt the mast fully
- Found a defect? Tag it out, pull the key, report it
- Log the inspection before first load
- Warning: Never operate a tagged-out truck
- Warning: A defective truck can kill: when in doubt, park it
Compliance checklist
- Every PIT is examined before being placed in service each day or shift(29 CFR 1910.178(q)(7))
- Trucks with safety-affecting defects are removed from service until repaired(29 CFR 1910.178(p)(1))
- Only trained, evaluated, and certified operators perform inspections and operate trucks(29 CFR 1910.178(l)(1))
- Inspection records are completed and retained per facility policy
Training and review
- Train everyone in scope before they work to this SOP: 2 sign-off sessions, one per shift.
- Retrain on each new revision. This SOP is reviewed every year by the warehouse manager.
Regulatory references
- 29 CFR 1910.178(q)(7), Powered industrial trucks: examination before use
- Industrial trucks must be examined before being placed in service and shall not be placed in service if the examination shows any condition adversely affecting safety. Examinations must be made at least daily, or after each shift when trucks are used around the clock.
- 29 CFR 1910.178(p)(1), Powered industrial trucks: trucks in need of repair
- Any power-operated industrial truck not in safe operating condition must be removed from service, and all repairs must be made by authorized personnel.
- 29 CFR 1910.178(l)(1), Powered industrial trucks: operator training
- Under paragraph (l)(1)(i) the employer must ensure each operator is competent to operate a powered industrial truck safely, demonstrated by successful completion of the training and evaluation this paragraph requires, before the operator may operate a truck without direct supervision. Certification of that training and evaluation is required separately by paragraph (l)(6).
Industrial trucks shall be examined before being placed in service, and shall not be placed in service if the examination shows any condition adversely affecting the safety of the vehicle.
Training sign-off
I have read and understood the Forklift Pre-Shift Inspection SOP, I have had the opportunity to ask questions, and I agree to perform the inspection before operating any powered industrial truck.
Draft from the Forklift Pre-Shift Inspection template. Have a qualified safety professional review it against how your floor actually runs before it goes into service. Informational, not legal advice.